Wingetlywingetly
← All apps

CoolTools

by IPUv1.1.1

Last updated

CoolTools is a collection of simulation models for refrigeration systems and each of them has a specific purpose e.g. cycle analysis, sizing of main components, energy analysis and optimization

Visit homepage

Install with winget

$ winget install --id IPU.CoolTools --exact --version 1.1.1

Run in Command Prompt, PowerShell, or Windows Terminal. Prompts for any agreements.

Silent install command for CoolTools

CoolTools uses EXE (Inno Setup). The silent install switches are /VERYSILENT /SUPPRESSMSGBOXES /NORESTART.

One-line silent install (x64, machine scope)
cooltools-v111.exe /VERYSILENT /SUPPRESSMSGBOXES /NORESTART

See the full silent install reference for CoolTools →

Built by Pckgr

For Intune admins

Stop chasing app updates. Pckgr patches them for you.

Automated application patching for Microsoft Intune. Pckgr keeps a curated library of 1,000+ apps continuously up-to-date in your tenant via Microsoft Graph - no manual repackaging, no chasing vendor sites.

Start free 30-day trial

From $49/month. No credit card required.

Not on Intune? Pckgr RMM deploys and patches apps like this one on any Windows fleet. Free for up to 5 devices.

About

CoolTools is a collection of simulation models for refrigeration systems and each of them has a specific purpose e.g. cycle analysis, sizing of main components, energy analysis and optimization. CoolTools is still under development, but it aims to become a replacement for the old CoolPack software supporting new refrigerant and cycle models.

The following simulation purposes are covered:

- Cycle analysis (process design) – comparison of one stage direct expansion cycle and one stage flooded cycle.

- System sizing – calculation of component sizes from general criteria.

- System simulation – calculating operating conditions in a system with known components.

- Component calculations – calculation of components efficiencies and outlet conditions.

- Evaluation of operation – evaluation of system efficiency.

- Process investigation – e.g. moist air calculations.

CoolTools is modern adaptation of CoolPack, a collection of simulation models that was developed in the 90’s the Department of Mechanical Engineering (MEK), Section of Thermal Energy (TES) at the Technical University of Denmark (DTU). More info on CoolPack can be found in IPU’s homepage: https://www.ipu.dk/products/coolpack/.

Installers · v1.1.1

ArchitectureTypeScopeInstallDownload
x64EXE
Inno Setup
machineDirect

Copy a command tailored to that specific architecture, type, and scope - useful when winget would otherwise pick a different default.

Security

No known CVEs for CoolTools.

Coverage is best-effort and depends on a winget package mapping to an NVD CPE entry. Absence here is not a guarantee of safety.

Related apps

  • CoolPackIPU
    IPU.CoolPackv1.50

    An old collection of simulation models for refrigeration systems, such as cycle analysis, sizing of main components, energy analysis and optimization.

  • Simple One Stage CO2 CycleIPU
    IPU.SimpleOneStageCO2Cyclev3.02

    Simple one-stage CO2 is primarily intended for teaching purposes. The application lets the user play with transcritical CO2 cycles: standard, gas-bypass and ejector cycle.

  • Pack Calculation ProIPU
    IPU.PackCalculationProv5.7.0.0

    A simulation tool for calculating and comparing yearly energy consumption of refrigeration and heating systems.

  • SecCoolIPU
    IPU.SecCoolv2.1.0.0

    A program for calculating, comparing and plotting thermophysical properties of secondary refrigerants.

  • DWSIMDaniel Medeiros
    DanWBR.DWSIMv9.0.5

    DWSIM is a Steady-State and Dynamic Sequential Modular Chemical Process Simulator for Windows, Linux and macOS.

  • LeaklogSZ CHKT
    SZCHKT.Leaklogv2.3.3

    Leakage control system based on Regulation (EC) No 842/2006.

More from IPU or browse refrigeration, thermodynamics.

Frequently asked questions

How do I install CoolTools on Windows?
Open Windows Terminal, PowerShell, or Command Prompt and run: winget install --id IPU.CoolTools --exact --version 1.1.1. winget downloads the installer from IPU and runs it. Requires Windows 10 (1809+) or Windows 11.
How do I install CoolTools silently for unattended deployment?
Add --silent and accept the agreements upfront: winget install --id IPU.CoolTools --exact 1.1.1 --silent --accept-package-agreements --accept-source-agreements. This is the variant Intune, Configuration Manager, and other deployment tools should use.
What are the silent install switches for CoolTools?
CoolTools uses EXE (Inno Setup). Run the downloaded installer with: cooltools-v111.exe /VERYSILENT /SUPPRESSMSGBOXES /NORESTART. The silent switches are /VERYSILENT /SUPPRESSMSGBOXES /NORESTART.
How do I uninstall CoolTools via winget?
Run: winget uninstall --id IPU.CoolTools --exact. Add --silent for unattended uninstalls. winget will use the registered uninstaller from CoolTools's Apps & Features entry.
Is CoolTools free?
CoolTools is distributed under Freeware. Refer to the publisher (https://www.ipu.dk/products/cooltools/) for the full license terms - Wingetly itself does not charge for installation.
Does CoolTools work on Windows 10?
Yes, as long as your Windows 10 build supports winget (1809 or newer). winget ships with App Installer on Windows 10/11 and pulls CoolTools directly from the publisher.
How do I keep CoolTools up to date?
Run winget upgrade --id IPU.CoolTools --exact, or winget upgrade --all to update everything winget tracks. We index 2 versions of CoolTools from microsoft/winget-pkgs.

Recent versions

  • 1.1.1latest
  • 1.1.0